Color: 1.75mm 0.75kg Tpu95, Black
Was a pain to feed into my Prusa Mk3 and I had to tweak the idler tension, but once I got it "right", the "amazon basics TPU" preset in PrusaSlicer is all I needed to set. Great adhesion to the textured sheet - first layer calibration has a lot of leeway since this stuff sticks so well.
Reviewed in the United States on July 29, 2023 by Mike
-
-
-
-
-
Vibrant color and good results*
Color: 1.75mm 0.75kg Tpu95, Orange
This filament was a bit tricky as it required very slow printing speeds to get good results on my Bambu Lab X1C. That being said, after dialing in the settings just right, I was able to get great results.
Reviewed in the United States on July 19, 2023 by Jason Cupkey
-
-
-
-
-
used the TPU for tires for my grandsons Sandy Buggy model, came out very nice and shiny.
Color: 1.75mm 0.75kg Tpu95, Black
the plastic worked very well. bed adhesion was very good. almost too good. maybe a good idea to use something on the bed to act as a release. (glue stick, hair spray, tape...)
Reviewed in the United States on July 5, 2023 by steven j smith steven j smith
-
-
-
-
-
made phone cases with this
Color: 1.75mm 0.75kg Tpu95, Orange
great quality
Reviewed in the United States on July 24, 2023 by josephreeves4
-
-
-
-
-
Good TPU Filament for Printing Phone and Tablet Cases
Color: 1.75mm 0.75kg Tpu95, Black
I printed a case for a little-known Android tablet. Keeping the walls pretty thick made this stay pretty stiff and at least a bit more childproof. It's worked so far. I printed this at 230°C using a 0.6mm nozzle. It likes to be hotter than typical PLA temperatures.
Reviewed in the United States on May 30, 2023 by Un cheval sans nom Un cheval sans nom
-
-
-
-
-
Excellent material as always
Color: 1.75mm 0.75kg Tpu95, Blue
PolyMaker has built a reputation around quality filament and this does not disappoint. Make sure you use a direct drive extruder to print it though.
Reviewed in the United States on May 7, 2023 by Cory C. Lunde
Color: 1.75mm 750g Tpu90, Teal
Good quality flexible filament and color is perfect. Had no problems printing a phone case for my sister with it.
Reviewed in the United States on February 16, 2023 by Saul
I was skeptical that my Ender 3 (with stock bowden extruder) would be able to print with this filament but it pulled it off no problem with some slicer tweaks. I used PrusaSlicer to generate the g-code for my tires and my tweaks were: 225C print temp, 30mm/s print speed, 3 shells (thicker wall=stiffe
r part), retraction length: 3mm, Extra Length on Restart: 1mm, ( I turned off Ensure Vertical Shell Thickness, that speed up the prints and reduced the number of retractions improving my results a bunch) And the filament stuck wonderfully to the default textured PEI my printer came with. --CRITICAL YOU MUST CHANGE THE RETRACTION SETTINGS (see image for my settings)-- Flexible filaments are prone to stringing it's just how they are, try to print only one object at a time and clean up stingers with sharp scissors A note on Bridging with flex filaments: IT SUCKS so if you have to do it use a ton of top shells (8+), decrease the layer height of the top with the slicer's variable layer height feature, this will give you the most chances to fully bridge, and change the bridging flow rate to 0.75. Just remember: Print Hot, Print Slow.
...
show more
Reviewed in the United States on March 12, 2022 by 2shophome 2shophome
